 |
|
|
|
| |
100KHz
HANDHELD LCR METER
MT4080A / MT4080D |
|
| |
Features
ESR measurement
Built-in infrared Port
SMD test probe (options)
Open and short calibration
Transformer measurement
Specifications
Standard/Optional Test Fixtures/Accessories 
Download:
Remote binning software tool |
Characteristics: |
|
| The MT4080A/MT4080D
LCR Meter is the first handheld meter of this type on the market, with a wide
range of test frequencies up to 10KHz (MT4080D) or 100KHz (MT4080A) and many measurement
parameters including Z, L, C,DCR, ESR, D, Q and q
as well. The MT4080A/MT4080D is design for both
component evaluation on the production line and fundamental impedance testing
for bench-top applications. With a build-in direct test fixture you can test the
lead components very easily. The 4-wire test clip can give a convenient connection
to larger components and assemblies with the accuracy of 4-wire testing. The LCR meter offers fast, reliable,and versatile testing at
low cost.Furthermore, the optional RS232C interface (IrDA) is an attractive, cost-effective
solution for quality assurance and incoming inspection operations,making the MT4080A/MT4080D
is the most advanced handheld LCR meter available on the market today. |
|
| |
Features |
|
|
| |
- Measurement parameters : Z, L, C, DCR, ESR, D, Q and q
- Test conditions : 100Hz, 120Hz, 1KHz, 10KHz, 100KHz(MT4080 only), 1Vrms, 0.25Vrms,
0.05Vrms 1Vdc ( for DCR )
- 0.2% basic accuracy
- Dual LCD display
- Very quickly response
- Fully auto/manual selection
- DC resistance measurement
- Rechargeable battery/ AC powered
- User friendly
- Infrared Interface ( RS 232C)
|
|
| |
ESR
measurement
|
|
|
| |
In today's switching mode power supply design,
higher frequency is reached everyday to take advantage of the size and output
power barrier. To ensure the performance of the circuit, the Equivalent Serial
Resistance (ESR) in a capacitor is the key element determining efficiency and
performance. With MT4080a/MT4080D the user can quickly
check the ESR of a capacitor up to 100KHz or 10KHz without hesitation. |
|
| |
Built-in
infrared Port
|
|
|
| |
MT4080A/MT4080D comes
with a built-in infrared port to allow communication with a personal computer.
With the fully Remote Control Command (RCC) support, both units are able to act
as an automatic LCR testing system; this is especially applicable in automatic
Q.A and I.Q.C testing. The user is able to control the measurements and get the
measured values through the IrDA port. Remote-Binning feature, easily sorting
the components, is combined with remote-binning software and infrared port.
|
|
| |
SMD
test probe(optional)
|
|
|
| |
Surface_mount components are usually tiny and have
no wire leads, making it more difficult to test surface_mount devices than conventional
components. The TL08 SMD test probe gives users an easy way to conduct SMD component
testing.The uniquely designed SMD test probe can also be used to test conventional
components if the wire leads are too short to insert into the test terminals.
|
|
| |
Open
and short calibration |
|
| |
In the world of LCR meters, open and short calibrations
are important procedures before making any measurements, especially when user
changes the testing frequency and level. Therefore, very fast open and short calibrations
are the key factors to the user. Within just 10 seconds, the user can perform
open or short calibrations at any frequency and level that he desires. |
|
| |
Transformer
measurement
|
|
|
| |
To qualify xDSL transformers, you can measure the
primary inductance or coupling capacitance at 10KHz and leakate inductance at
100KHz with lower test voltage. You can also measure the DC-resistance of primary
and secondary with the standard DCR function.
|
|
| |
|
|
|
|
